Studio 5000 Architect provides a design environment optimized for the management of reusable engineering content in multiple controller and HMI automation systems. With Studio 5000 Architect you can jump start your initial system creation for your control and visualization applications.
ORDERING INFORMATION
Studio 5000 Architect™ activates with Logix Designer Full, Standard, and Pro licenses
Studio 5000 Architect™ can also be purchased standalone
Studio 5000 Architect 2.0 is included in the Studio 5000 Logix Designer V30 media release

FactoryTalk® Gateway is the next generation, highest performing Classic OPC DA data server for the Logix5000 controller family. FactoryTalk® Gateway utilizes RSLinx® Enterprise and FactoryTalk® Live Data
to distribute and share control system data. This gives you the fastest data rates and capacity possible, while minimizing the impact on your automation networks and controllers. FactoryTalk® Gateway delivers a fully scalable solution from small applications running on a single PC and a single controller to large distributed and even redundant data server configurations communicating to higher volume of controllers. The FactoryTalk® Gateway is available with multiple tag quantities from 5 thousand, 32 thousand, 75 thousand and unlimited editions so that you can acquire just enough to meet your application’s needs.

RSLinx® Classic is the most widely-installed Communications software in automation today. All editions of RSLinx® Classic deliver the ability to browse your automation networks, configure and diagnose network devices. RSLinx® Classic Lite is included at no extra cost with most Rockwell Automation design software so that you can manage and maintain your control system. RSLinx® Classic “Single Node”, “OEM” and “Gateway” editions provide both DDE and Classic OPC DA data servers to permit 3rd party software to access information within your control devices. RSLinx Classic “Single Node” permits a 32bit application running on the same PC with RSLinx Classic to interface with a single controller. RSLinx® Classic “OEM” goes further by communicating with a moderate number of controllers. RSLinx® Classic “Gateway” expands this to support 64 bit applications that are running either on the same PC or a remote PC using Ethernet to pass information between the computers. The “Gateway” edition of RSLinx® Classic can also act as a centralized network connection point for multiple computers running RSLinx® Classic so that you can centralize the administration of your network configuration.

The RSLogix™ family of IEC-1131-compliant ladder logic programming packages helps you maximize performance, save project development time, and improve productivity. This family of products has been developed to operate on Microsoft Windows® operating systems. RSLogix 5 supports the Allen-Bradley PLC-5® family of programmable controllers.

The RSLogix 5 programming package is compatible with programs created with Rockwell Software DOS-based programming packages for the PLC-5 processors, making program maintenance across hardware platforms convenient and easy.

The RSLogix™ family of IEC-1131-compliant ladder logic programming packages helps you maximize performance, save project development time, and improve productivity. This family of products has been developed to operate on Microsoft Windows® operating systems. Supporting the Allen-Bradley SLC™ 500 and MicroLogix™ families of processors, RSLogix™ 500 was the first PLC® programming software to offer unbeatable productivity with an industry-leading user interface.

RSLogix 500 programming package is compatible with programs created with Rockwell Software DOS-based programming packages for the SLC 500 and MicroLogix families of processors, making program maintenance across hardware platforms convenient and easy.

Studio 5000 Logix Designer is the one application to configure, program and maintain the entire Allen-Bradley® Logix 5000 family of controller’s products and related devices. Its intuitive programming environment allows users to work collaboratively to design and maintain their systems.

FactoryTalk® AssetCentre provides you with a centralized tool for securing, managing, versioning, tracking and reporting automation related asset information across your entire facility. It can do this automatically, with limited additional management oversight or work from employees. FactoryTalk AssetCentre can impact uptime, productivity, quality, employee safety or regulatory compliance.

With FactoryTalk AssetCentre, you can:

Secure access to the system
Track detailed users’ actions
Automatically track firmware versions
Manage historical versioning of any electronic file
Provide automatic backup and compare operations on supported devices
Add backup and compare plug-ins for 3rd party vendor devices
Configure process instrumentation
Manage instrumentation calibration schedules and certificates

Studio 5000 virtual design increases design productivity, reduces risk, and decreases overall project costs. Studio 5000 Logix Emulate is at the core of Studio 5000 virtual design, which enables Machine Prototyping, Throughput Analysis, Virtual Commissioning and Operator Training Solutions (OTS). Logix Emulate provides the ability to validate, test and optimize application code independent of physical hardware. New interface capabilities provide connectivity to 3rd party simulation and Operator Training Systems allowing users to simulate their entire process and train teams in a safe, virtual environment.

Application Code Manager is a tool that enables more efficient project development with libraries of re-usable code. You can create modular objects with customizable configuration parameter using the re-usable content, allowing you to specify the pertinent information on how the object should be used in a project. Application Code Manager creates not only the coding for the modular object but also the associated visualization, historical and alarming elements.

Studio 5000 View Designer is the design environment for the PanelView 5000 family of operator terminals. The integration of the PanelView 5500 with Studio 5000 View Designer helps you bulid modern applications more easily and improve operator performance with an intuitive design environment.

With a common launcher for creating projects as Logix Designer, you can enter configuration information once and leverage it across the entire automation design system, providing new levels of integrated design, operations, and maintenance.

Studio 5000 Logix Designer is the one application to configure, program and maintain the entire Allen-Bradley® Logix 5000 family of controller’s products and related devices. Its intuitive programming environment allows users to work collaboratively to design and maintain their systems.

RSNetWorx™ products provide design and configuration management services for open standard networks from ODVA, including ControlNet, DeviceNet and EtherNet/IP. RSNetWorx allows you to achieve maximum productivity with your ControlNet and DeviceNet installations. You will be able to define and configure the devices on your network quickly through a simple software interface. This definition can take place offline using drag and drop operations or online by using RSLinx® to browse a ControlNet or DeviceNet network.

Before you can optimize production, you need to understand where efficiencies can be gained in your plant. To do this, you need a clear view across entire lines and production processes. FactoryTalk® View Site Edition (SE) is a supervisory-level HMI software for monitoring and controlling distributed-server/multi-user applications. It provides a comprehensive and accurate picture of operations, meeting the demands of multiple stakeholders including engineering, maintenance, operations, and production Information Technology (IT).

FactoryTalk View SE provides robust and reliable functionality in a single software package that scales from a stand-alone HMI system to a distributed visualization solution. As our customers have experienced over the past few years, FactoryTalk View SE enables you to take advantage of mobility, virtualization, and other new technologies, meeting HMI challenges in process, batch and discrete applications and delivering critical visibility when and where you need it.

FactoryTalk® View Machine Edition (ME) software is a versatile HMI application that provides a dedicated and powerful solution for machine-level operator interface devices. As an integral element of the Rockwell Automation visualization solution, FactoryTalk View Machine Edition provides superior graphics, run-time user management, language switching and faster commissioning time through a common development environment.

FactoryTalk View Machine Edition allows for a consistent operator interface across multiple platforms, including PanelView Plus and Windows desktop solutions and consists of:

FactoryTalk View Studio: Configuration software for developing and testing HMI applications.
FactoryTalk View ME Station: A traditional “stand-alone” HMI solution that provides an integrated operator interface that runs the same HMI application on PanelView™ Plus 7, PanelView™ Plus 6, MobileView™ terminal, Rockwell Automation Industrial Computers, or other industrial PC.

On the road, at home or in the office, FactoryTalk® ViewPoint provides a secure interface with FactoryTalk View’s graphics, trending, and alarming applications through a Web browser. FactoryTalk ViewPoint extends the access to FactoryTalk View Site Edition (SE) and Machine Edition (ME) applications to user’s mobile devices for improved real-time decision making.

As an add-on to FactoryTalk® View SE and PanelView™ Plus, FactoryTalk ViewPoint delivers a rich, interactive experience that includes real-time and historical trending. You gain the simplicity of standard browser navigation and new degrees of access to critical FactoryTalk View information all in a web browser. There is no client software to install and maintain, lowering total cost of ownership.

Monitoring and controlling automation machines and processes demands versatility and the scalability to connect to a host of open technologies. RSView®32™ is an integrated, component-based HMI for monitoring and controlling automation machines and processes. RSView32 expands your view with open technologies that provide unprecedented connectivity to other Rockwell Software products, Microsoft products, and third-party applications.

Core functionality provides the versatility to accommodate a range of integration needs – from the machine to the production line to the entire plant. RSView32 is an open system that allows plant floor data to be shared with other manufacturing systems, providing real-time manufacturing information throughout the enterprise.

Designed for Microsoft® Windows® environments, RSView32 interacts easily with the Rockwell Software integrated product line, Microsoft products, and other third-party offerings.

The FactoryTalk® ProductionCentre® solution integrates quality management and business analytics with paperless shop floor and repair execution. This improves operational efficiencies while ensuring regulatory compliance and the highest levels of quality. This total plant solution enables you to improve quality and global operational efficiencies, reduce costs of regulatory compliance, accelerate time to market, and share real-time data on quality.

Find operational performance and business improvements with our ERP Integration Gateway, a cost-effective application that aligns manufacturing operations with the business processes and information housed in Enterprise Resource Planning (ERP) and other business systems. You gain an agility that makes the enterprise more responsive to customer demands, more competitive, and more profitable.

Are you struggling to gain insights from your manufacturing data? Do your operators have real-time data in their line of sight? What is your data hiding from you?

Manufacturing analytics tools collect your raw data and turn it into actionable information. Sounds easy? There are many ways to manage information, but the key is the action you are able to take from that information and how high the hurdle is before getting to the data.

Starting with a specific problem to solve – such as improving OEE or improving yield – is a great way to pinpoint what type of analytics you may need, where the data comes from to solve that problem, and who needs the information to make the decision.

Scalable analytics from Rockwell Automation are the right choice, right size for you. From an Industrial IoT sensor to machines — all the way through your enterprise, we can help you with the right application and remove barriers to success.

Take a look at some analytics applications recently added to our family of Manufacturing Intelligence & Analytics products and services.

FactoryTalk® VantagePoint EMI is a powerful web-based manufacturing business intelligence solution that integrates all data into a single information management and decision support system. Designed specifically for industrial environments with premier Logix integration, VantagePoint connects to your Logix controllers, OPC data sources, Historians, and SQL / Oracle Databases to deliver best in class manufacturing intelligence. Access your data from anywhere including your shop floor devices, PC, or your mobile phone or tablet in order to make smart decisions that increase your productivity from anywhere!
BENEFITS:
Overcome economic challenges
Reduce costs
Optimize production capabilities
Improve sustainability results
Conserve energy
Minimize scrap and waste
Bolster best practices and regulatory compliance
Increase global competitiveness
Aggregate manufacturing information across all assets and resources
Reduce demand forecast errors
Assure customer commitments and satisfaction
Increase production agility
Shorten product development and launch cycles
Monitor production variants
Enhance overall product quality
Overcome asset constraints
Maximize resource utilization

The FactoryTalk® Historian Site Edition (SE) application provides you with the data capture, management, and analytical capabilities to help generate improved decision-making. ​Plant supervisors can view individual historical data for machines, process equipment, or production lines on demand. Production supervisors can analyze batch operations for an individual site against ente​rprise-wide corporate production parameters. Enterprise managers can compare KPIs among locations. This application helps locate and correct sources of inefficiencies quickly. This helps you manage manufacturing consistency, energy use, first-pass quality, and other factors that can improve the bottom line.

FactoryTalk® Historian Machine Edition (ME) provides high-speed, reliable data capture, enabling manufacturers to reach continuous process improvement goals. It achieves its superior reliability through a solid state design hardened for on-machine use and with no moving parts. A limited software footprint requires no server or PC, significantly reducing the risk of data loss due to network or other system interruption and making the unit ideal for remote or hard to service locations.
BENEFITS
Embedded historian in the backplane
10+ times faster data collection rates than traditional historians
Lowers total cost of ownership – no dedicated computer or special client/software needed to configure
Robust and reliable data collection application
Perform tasks in a rich, interactive browser experience for configuration and simple reports
Allows OEM’s to utilize a full-fledged historian in their skids for data collection

FactoryTalk® Metrics gives you the data that can reveal new ways to increase production, reduce costs, and increase quality. By generating accurate reporting of real plant floor activity, this software gives you important insights into using existing equipment and labor more effectively. FactoryTalk Metrics reports on OEE (Overall Equipment Effectiveness), but it is more than just an OEE reporting tool. OEE can tell you how a machine is performing over time; it cannot tell you why the machine is performing at that level. FactoryTalk Metrics answers the “why” question, uncovering the root-causes of downtime and loss helps you make real improvements to performance.

FactoryTalk® EnergyMetrix is a web-enabled management software package that gives you access to critical energy information from virtually any location. The software combines date communication, client-server applications, and Microsoft’s advanced .NET™ Web technology to provide you with a complete energy-management decision support tool.

With FactoryTalk EnergyMetrix, you can capture, analyze, store, and share energy data with key stakeholders using a standard web browser. This makes it simple to distribute the knowledge necessary to optimize energy consumption, manage power quality, correlate energy usage, determine cost to production, negotiate energy rates, and improve efficiency.

Manage your manufacturing processes by integrating the critical data from your shop-floor with enterprise IT and other manufacturing applications. Think of the power. FactoryTalk® Transaction Manager can take an industrial transaction and tightly link it to multiple systems so they act as one. This helps you establish an end-to-end link, giving you reliability to support enterprise-wide integration.

In many cases, FactoryTalk Transaction Manager is used in data-logging situations where production data from the control system needs to be saved in a database. Different from a historian application, this software provides a two-way exchange of data between applications, like between a database and a control system for downloading production work orders for example. FactoryTalk Transaction Manager offers new levels of integration and visibility into many of these critical data transactions.

The HART (Highway Addressable Remote Transducer) protocol is a widely accepted standard for digitally enhanced communication with instrumentation within the process industries.

Our Bulletin 1788 Redundant EtherNet/IP™ to FOUNDATION Fieldbus (H1) Linking Device provides a fast and integrated solution for adding FOUNDATION Fieldbus devices to any Logix platform.

Our Bulletin 1788 EtherNet/IP™ to DeviceNet Linking Devices provide a fast and integrated solution for adding DeviceNet™ to a new, or existing system. Built-in remote access capabilities enable the ability to control, configure, and troubleshoot devices on the DeviceNet network through automated device management.

Our Bulletin 1788 Redundant ControlNet™ to Profibus-PA Linking Device provides a fast and integrated solution for adding Profibus-PA field devices to any Logix platform. This linking device provides a direct link between Profibus-PA and ControlNet without requiring an intermediate Profibus-DP layer.

Our Bulletin 1788 Redundant ContolNet™ to FOUNDATION Fieldbus (H1) Linking Device provides a fast and integrated solution for adding FOUNDATION Fieldbus devices to any Logix platform.

Our Bulletin 1788 6-way Intelligent Fieldbus Junction Box provides a fault-tolerant method for connecting field devices to a Profibus-PA or FOUNDATION Fieldbus (H1) network. The unit comprises a bus-input port, bus-output port, and six field device drop-line ports. Each drop-line port’s bus current is continuously monitored. If a fault is detected, the drop is isolated until the fault is corrected. Even with one of the segments shorted, all remaining field devices on the bus are able to communicate.

Our Bulletin 1788 4-way Redundant Intelligent Fieldbus Junction Box provides a simple, redundant, and fault-tolerant method for connecting field devices to a Profibus-PA or FOUNDATION Fieldbus (H1) network. The unit provides segment protection to four field device drop-line ports by continuously monitoring drop currents and disconnecting a faulty drop to protect the rest of the segment when a fault is detected. Trunk monitoring in redundant configurations enables the rerouting of trunk messages around cable faults.

Our Bulletin 1783 Stratix® 8300 Layer 3 Modular Managed Switch line uses the current Cisco® Catalyst® switch architecture and feature set along with powerful configuration tools, helping to provide secure integration with the enterprise network using tools familiar to IT professionals. Configuration and monitoring tools provide secure integration to the enterprise network and allow easy setup and diagnostics with our Integrated Architecture® system. This Layer 3 switch supports routing between VLANs and subnets.

Our Bulletin 1783 Stratix® 8000 Modular Managed Switch line uses the current Cisco® Catalyst® switch architecture and feature set along with powerful configuration tools, helping to provide secure integration with the enterprise network using tools familiar to IT professionals. Configuration and monitoring tools provide secure integration to the enterprise network and allow easy setup and diagnostics with our Integrated Architecture® system.

Our Bulletin 1788 Redundant EtherNet/IP™ to Profibus-PA Linking Device provides a fast and integrated solution for adding Profibus-PA field devices to any Logix platform. These linking devices provide a direct link between Profibus-PA and EtherNet/IP without requiring an intermediate Profibus-DP layer.

IO-Link Technology is a worldwide open-standard protocol that integrates sensors into our Connected Enterprise by connecting the IO-Link enabled device into an IO-Link master module. You can deliver data from the sensor directly into a control system in a very efficient manner. The flexibility of IO-Link capable sensors allows machines to operate more effectively by providing the controller with diagnostics. In addition to product detection, sensors provide detailed and accurate machine health status to improve uptime and increase productivity.

IO-Link enabled sensors offer advanced features and diagnostics that can only be accessed through an IO-Link master module. These sensors act like standard sensors when not interfaced to an IO-Link enabled control system, so you can stock the same sensors for standard I/O (SIO) applications and IO-Link applications, simplifying the selection process and reducing stocking costs.

Our Bulletin 1788 Redundant ContolNet™ to FOUNDATION Fieldbus (H1) Linking Device provides a fast and integrated solution for adding FOUNDATION Fieldbus devices to any Logix platform.

Our Bulletin 1788 Redundant ContolNet™ to FOUNDATION Fieldbus (H1) Linking Device provides a fast and integrated solution for adding FOUNDATION Fieldbus devices to any Logix platform.

Our Bulletin 1788 6-way Intelligent Fieldbus Junction Box provides a fault-tolerant method for connecting field devices to a Profibus-PA or FOUNDATION Fieldbus (H1) network. The unit comprises a bus-input port, bus-output port, and six field device drop-line ports. Each drop-line port’s bus current is continuously monitored. If a fault is detected, the drop is isolated until the fault is corrected. Even with one of the segments shorted, all remaining field devices on the bus are able to communicate.

Our Bulletin 1788 4-way Redundant Intelligent Fieldbus Junction Box provides a simple, redundant, and fault-tolerant method for connecting field devices to a Profibus-PA or FOUNDATION Fieldbus (H1) network. The unit provides segment protection to four field device drop-line ports by continuously monitoring drop currents and disconnecting a faulty drop to protect the rest of the segment when a fault is detected. Trunk monitoring in redundant configurations enables the rerouting of trunk messages around cable faults.

Universal Remote I/O Link is a local area network designed to connect controllers to remote I/O chassis and a variety of intelligent devices such as operator interfaces and AC or DC drives.

SERCOS (Serial Real-time Communications System) is an internationally-approved communication standard for motion control (IEC 61491). This communication network is designed for high-speed serial communication of standardized closed-loop data, in real-time, over a noise-immune fiber-optic cable. We support SERCOS with interface motion modules which provide SERCOS drive connectivity and control for the ControlLogix® controller.

The DH‑485 industrial local area network is designed for factory-floor applications and uses the RS‑485 transmission standard.

The Data Highway Plus (DH+) network is a local area network designed to support remote programming and messaging between computers and controllers for factory-floor applications.

Our Bulletin 1783 Stratix® 6000 Fixed Managed Ethernet Switches are designed to help ease deployment of an Ethernet network on the plant floor. These switches offer CIP tags and configuration screens in the Studio 5000™ Logix Designer application, as well as faceplates for FactoryTalk® View HMI software for integration and diagnostics of networked devices.

Our Bulletin 1783 Stratix® 5950 security appliance combines several enhanced security functions into a single appliance to help protect your industrial automation infrastructure. As part of our security offering, this product builds on common network security technologies. These technologies help provide enhanced access control, threat detection, and application visibility in your industrial control system (ICS).

Our Bulletin 1783 Stratix® 5900 Services Router combines several modern security functions into a single appliance to protect your industrial automation and control systems network, not only at the perimeter, but also at the cell/zone level. This router is compact, robust, and industrially hardened to provide a variety of managed switching features.

Bulletin 1585 Ethernet Cable Spools supply a reliable network connection in harsh surroundings. The high speed data rate allows more data to be transferred within a shorter period of time. Red cable jackets let you easily identify safety applications. We offer unshielded twisted pair, shielded twisted pair, and 600V cables.

The Embedded Switch Technology embeds Ethernet switch features into your hardware to support high performance applications. Our dual-port products with the embedded switch feature let you connect devices directly to your network, without a separate Ethernet switch, helping to reduce overall cost and simplifying system configuration. These products support linear and device-level ring (DLR) topologies for EtherNet/IP™ applications.

ArmorStratix™ 5700 Industrial Ethernet Switches provide a dependable, rugged, on-machine solution for networks in extreme environments. This layer 2 managed switch is IP67-rated for dust and washdown protection, and is ideal for operations where widely distributed applications are required.

Thick and thin round cable (generally used for trunk and drop cable, respectively) are available in bulk spools or pre-molded cordsets or patchcords. We offer a wide variety of rugged, durable connectivity components for use in round cable systems. These components include t-Ports, DeviceBox™, DevicePort™, PowerTap™ and a multitude of other accessories. Stainless steel versions of round cable system components are also available for harsh industrial applications.